Cold Weather Warning
Colour Variation Information
Due to the variety of application and environmental issues likely to influence the curing of a cement-based grout joint, it is virtually impossible for the dry composition of the pre-blended grout powder to produce localised variations of shade and colour without first having been affected by any one of the following factors, all of which are beyond the control of the manufacturer.
Mix Consistency
It is essential to ensure the powder is mixed thoroughly and consistently with clean water, to form a smooth, lump-free paste. Mixing at high speeds will cause air bubbles which can affect the surface finish. Always use grout from the same batch to avoid any manufacturing variations.
Joint Preparation
All joints to be grouted must be of consistent depth and raked clean of any adhesive residues as any contaminant in the open joints will consequently result in irregularities in the depth and consistency of the freshly applied grout, both of which may result in shade variation.
Tiles Surface Cleaning and Joint Finishing
When wiping down to remove the excess mortar after applying the grout, care must be taken not to “over-wet” the freshly compacted joints, as this may affect water content in some joints but not in others, leading to a higher concentration of fine surface laitance and hence raising the possibility of a lighter shaded surface appearance in these areas. Brushing or dry wiping over a grouted joint when the paste has bodied up, but is still not set, can disturb the surface finish and open up the texture of the grout to give a coarser and darker shade than when the grout was first laid and finished off with a wet cloth or sponge. Any contact with the surface at this point in time must be even and consistent over all areas to ensure the hardened appearance retains an equivalent degree of dryness and surface texture, otherwise shade variations are likely.
General Surface Maintenance
Cleaning and maintenance of the completed tiled surface must ensure that the materials and cleaning agents used are applied consistently, are not used at excessive concentrations and are rinsed off promptly as soap and detergent residues can accumulate in joints and affect appearance, particularly when exposed to moisture.
Substrate Type
Variations in the density or porosity of the surface beneath the tiles will encourage some areas of the grout joints to dry out at a different rate to others, usually illustrated where darker areas of the grout are laid over dense or impermeable section of flooring, whereas lighter shades will be evident over the more porous and drier sections of the substrate flooring.
Service Conditions
The end use of the tiled location needs some consideration as this may result in some areas being exposed to wetting more frequently than others, which consequently will result in the damper sections appearing slightly darker than the drier areas. Regular and localised wetting of one area at a more frequent rate than the surrounding tiled area will result in a shade variation due to the moisture level retained within the cured tile joint.
Tile Type and Finish
Porous tiles, substrates or joints adjoining the cut edge of a tile will be exposed to greater risk of moisture absorption from the wet paste than less porous surfaces or true tile edges. This can produce localised variations in moisture content and when fully cured will manifest in a shade variation from joint to joint.
Summary
To maintain an ideal consistent appearance in all grout joints it is essential to ensure consistency is applied at all stages of the application process, including the type of tooling used to finish off joints, the amount of moisture introduced and allowed to remain when cleaning the tiled surface and the finish time which elapses between initially compacting the joints and then returning to tool the joints to a smooth clean edged finish.
Where any one of the above precautions is not followed then it is possible to encourage shade variation in the final colour of the hardened grout. It may be possible in some cases to restore joint colour with the application of Azpects Grout Residue Cleaner. It should be noted that in most cases the lightening of dark joints is due to blooms of efflorescence of naturally occurring lime which is released by drying cycles from within the Portland cement base. This is often a transient feature as the natural cycles of wet and dry periods following cleaning or exposure to weather (if external) will result in the surface stabilising to a consistent shade as the lime is washed away.
One of the most reported issues with a cement-based grout is colour variation and cracking down the length of a joint. Both of these issues are due to improper product application, whether it is too much water left after final cleaning, or that moisture is trapped in voids in the bedding mortar. None of these issues are because of the product failing.
Efflorescence
If the joint surface develops a white surface after drying, it is caused by water/moisture moving to the surface which brings soluble salts to the surface. New concrete and mortar are especially prone to efflorescence because they contain more free calcium compounds that can be carried to the surface during curing.
Should you do anything?
If it’s a new installation and the deposits are light, it’s often reasonable to wait. Rain and normal weathering may remove much of the residue, and future deposits may become less frequent. Cleaning the surface with EASYCare Grout Residue Cleaner will remove surface efflorescence, however the prescence of moisture in the joint may cause more to appear.